LIN Core System Basis Chip 32-Pin HTSSOP T/R

The UJA1079A core System Basis Chip (SBC) replaces the basic discrete components commonly found in Electronic Control Units (ECU) with a Local Interconnect Network (LIN) interface. The UJA1079A supports the networking applications used to control power and sensor peripherals by using the LIN interface as a local sub-bus. The core SBC contains the following integrated devices: In addition to the advantages gained from integrating these common ECU functions in a single package, the core SBC offers an intelligent combination of system-specific functions such as: The UJA1079A is designed to be used in combination with a microcontroller. The SBC ensures that the microcontroller always starts up in a controlled manner.

2.1 General

• Contains LIN ECU functions:
  • LIN transceiver
  • Scalable 3.3 V or 5 V voltage regulator delivering up to 250 mA for a microcontroller and peripheral circuitry; an external PNP transistor can be connected for better heat distribution over the PCB
  • Watchdog with Window and Timeout modes and on-chip oscillator
  • Serial Peripheral Interface (SPI) for communicating with the microcontroller
  • ECU power management system
• Designed for automotive applications:
  • Enhanced ElectroMagnetic Compatibility (EMC) performance
  • ±8 kV ElectroStatic Discharge (ESD) protection Human Body Model (HBM) on the LIN bus pin and the wake-up pins
  • ±6 kV ElectroStatic Discharge protection IEC 61000-4-2 on the LIN bus pin and the wake-up pins
  • ±58 V short-circuit proof LIN bus pin
  • Battery and LIN bus pins are protected against transients in accordance with ISO 7637-3
• Small 6.1 mm × 11 mm HTSSOP32 package with low thermal resistance
• Pb-free; Restriction of Hazardous Substances Directive (RoHS) and dark green compliant

LIN transceiver

• LIN 2.1 compliant LIN transceiver
• Compliant with SAE J2602
• Downward compatible with LIN 2.0 and LIN 1.3
• Low slope mode for optimized EMC performance
• Integrated LIN termination diode at pin DLIN

Power management

• Wake-up via LIN or local wake-up pins with wake-up source detection
• 2 wake-up pins:
  • WAKE1 and WAKE2 inputs can be switched off to reduce current flow
  • Output signal (WBIAS) to bias the wake-up pins, selectable sampling time of 16 ms or 64 ms
• Standby mode with very low standby current and full wake-up capability; V1 active to maintain supply to the microcontroller
• Sleep mode with very low sleep current and full wake-up capability

Control and diagnostic features

• Safe and predictable behavior under all conditions
• Programmable watchdog with independent clock source
  • Window, Timeout (with optional cyclic wake-up) and Off modes supported (with automatic re-enable in the event of an interrupt)
• 16-bit Serial Peripheral Interface (SPI) for configuration, control and diagnosis
• Global enable output for controlling safety-critical hardware
• Limp home output (LIMP) for activating application-specific ‘limp home’ hardware in the event of a serious system malfunction
• Overtemperature shutdown
• Interrupt output pin; interrupts can be individually configured to signal V1 undervoltage, LIN/local wake-up and cyclic and power-on interrupt events
• Bidirectional reset pin with variable power-on reset length to support a variety of microcontrollers
• Software-initiated system reset

Voltage regulator V1

• Scalable voltage regulator for the microcontroller, its peripherals and additional external transceivers
• ±2 % accuracy
• 3.3 V and 5 V versions available
• Delivers up to 250 mA and can be combined with an external PNP transistor for better heat distribution over the PCB
• Selectable current threshold at which the external PNP transistor starts to deliver current
• Undervoltage warning at 90 % of nominal output voltage and undervoltage reset at 90 % or 70 % of nominal output voltage
• Can operate at V_BAT voltages down to 4.5 V (e.g. during cranking), in accordance with ISO 7637 pulse 4/4b and ISO16750-2
• Stable output under all conditions