HighEnd MCU

The STM32F100xx value line family incorporates the high-performance ARM Cortex -M3 32-bit RISC core operating at a 24 MHz frequency, high-speed embedded memories (Flash memory up to 512 Kbytes and SRAM up to 32 Kbytes), a flexible static memory control (FSMC) interface (for devices offered in packages of 100 pins and more) and an extensive range of enhanced peripherals and I/Os connected to two APB buses. All devices offer standard communication interfaces (up to two I²Cs, three SPIs, one HDMI CEC, up to three USARTs and 2 UARTS), one 12-bit ADC, two 12-bit DACs, up to 9 general-purpose 16-bit timers and an advanced-control PWM timer.The STM32F100xx high-density value line family operates in the –40 to +85 °C and –40 to +105 °C temperature ranges, from a 2.0 to 3.6 V power supply. A comprehensive set of power-saving mode allows the design of low-power applications.The STM32F100xx value line family includes devices in three different packages ranging from 64 pins to 144 pins. Depending on the device chosen, different sets of peripherals are included, the description below gives an overview of the complete range of peripherals proposed in this family.These features make the STM32F100xx value line microcontroller family suitable for a wide range of applications such as motor drives, application control, medical and handheld equipment, PC and gaming peripherals, GPS platforms, industrial applications, PLCs, inverters, printers, scanners, alarm systems, video intercoms, and HVACs.

Core: ARM® 32-bit Cortex® -M3 CPU

24 MHz maximum frequency, 1.25 DMIPS /MHz (Dhrystone 2.1) performance

Single-cycle multiplication and hardware division

Memories

256 to 512 Kbytes of Flash memory

24 to 32 Kbytes of SRAM

Flexible static memory controller with 4 Chip Selects. Supports SRAM, PSRAM and NOR memories

LCD parallel interface, 8080/6800 modes

Clock, reset and supply management

2.0 to 3.6 V application supply and I/Os

POR, PDR and programmable voltage detector (PVD)

4-to-24 MHz crystal oscillator

Internal 8 MHz factory-trimmed RC

Internal 40 kHz RC

PLL for CPU clock

32 kHz oscillator for RTC with calibration

Low power

Sleep, Stop and Standby modes

V_BATsupply for RTC and backup registers

Serial wire debug (SWD) and JTAG I/F

DMA

12-channel DMA controller

Peripherals supported: timers, ADC, SPIs, I²Cs, USARTs and DACs

1 × 12-bit, 1.2 µs A/D converter (up to 16 ch.)

Conversion range: 0 to 3.6 V

Temperature sensor

2 × 12-bit D/A converters

Up to 112 fast I/O ports

51/80/112 I/Os, all mappable on 16 external interrupt vectors and almost all 5 V-tolerant

Up to 16 timers

Up to seven 16-bit timers, each with up to 4 IC/OC/PWM or pulse counter

One 16-bit, 6-channel advanced-control timer: up to 6 channels for PWM output, dead time generation and emergency stop

One 16-bit timer, with 2 IC/OC, 1 OCN/PWM, dead-time generation and emergency stop

Two 16-bit timers, each with IC/OC/OCN/PWM, dead-time generation and emergency stop

Two watchdog timers

SysTick timer: 24-bit downcounter

Two 16-bit basic timers to drive the DAC

Up to 11 communications interfaces

Up to two I²C interfaces (SMBus/PMBus)

Up to 3 USARTs (ISO 7816 interface, LIN, IrDA capability, modem control)

Up to 2 UARTs

Up to 3 SPIs (12 Mbit/s)

Consumer electronics control (CEC) I/F

CRC calculation unit, 96-bit unique ID